Electronic engine control for controlled and reliable operation
Electronic engine control systems control and monitor the key functions of an aircraft engine across different operating states. Silver Atena develops control units and functions for such engine control systems, combining system architecture, control unit development, embedded software, control development, safety, testing and qualification.
Challenges in engine control
An engine control system processes sensor information, setpoints and operating states in real time. From these, it derives control commands and keeps the engine within the defined operating limits. Speed, temperature and pressure respond in a coupled manner to fuel supply and other manipulated variables. High demands on availability and reliability apply in all operating phases, from start-up through steady-state and transient operating states to shutdown, even under demanding electrical, thermal and mechanical environmental conditions.
The system architecture provides the basis for aligning the control unit, sensors, actuators, control and communication within the engine system, taking the safety requirements into account.
The key requirements include:
- Capturing engine states: Measured variables such as speed, pressure or temperature provide the basis for control, monitoring and diagnostics.
- Combining control and protection: Safety-relevant control algorithms and protection mechanisms work together to keep the engine within its defined operating limits.
- Managing faults in a controlled way: Defined sensor, actuator, communication and computer faults are detected, assessed and handled with the responses defined for the system. Depending on the system, this includes redundancy, monitoring and defined degradation states.
- Preparing compliance demonstration: Development, verification and qualification are aligned with the requirements and the planned certification basis at an early stage. End-to-end traceability provides the basis for robust compliance demonstration.
Services for FADEC and engine control
Silver Atena develops electronic control systems for aircraft engines. One possible focus is FADEC systems (Full Authority Digital Engine Control). These are digital engine control systems with full authority over the engine functions assigned to them.
Engine and control unit architecture
The starting point is the functional, technical, operational and safety-related requirements, which are structured and managed by requirements engineering. The system architecture defines the interaction of control unit, sensors, actuators, communication and higher-level systems. Aspects considered include operating states, interfaces, redundancy, monitoring, fault responses and degradation states, as well as the integration and verification strategy.
FADEC and engine control units
Silver Atena develops electronic control units and associated functions for controlling and monitoring aircraft engines. Depending on the system boundary and project scope, this includes start-up and shutdown control, speed or power control, fuel flow control, sensor signal processing and the control and monitoring of actuators and operating limits. The functional scope and system boundaries depend on the engine, platform, system architecture, safety requirements and certification basis.
Control and function development
Control and function development creates algorithms for control, regulation, limiting and monitoring. They are based on the physical engine behaviour, available measured variables, actuator dynamics and permissible operating limits. Simulation and model-based development can help to investigate control strategies and fault responses before system integration.
Embedded software for engine control
The embedded software implements control, communication, diagnostic and hardware-related functions on the control unit. In safety-relevant applications, the focus is on deterministic behaviour, a clearly structured software architecture, traceability and requirements-based verification.
Hardware development for engine control units
Hardware development creates the electronic platform with processing units, sensor, actuator and communication interfaces, power supply, monitoring functions, protection circuits and, where required, redundant structures. The design is based on the functional, safety-related, electrical and environmental requirements.
Safety, redundancy and diagnostics
Safety engineering considers possible fault states, their effects and the required system responses. Depending on the system, plausibility checks, monitoring, diagnostics, redundancy and defined degradation strategies are used. The specific architecture is derived from the project-specific safety requirements and verified in the development process.
Development process for engine control
A typical process comprises the following steps:
- Analyse and validate requirements and engine function: Functional, technical, operational and safety-related requirements are analysed, validated and assigned to the relevant operating states, system boundaries and interfaces.
- Define the system and control unit architecture: Functions and interfaces are structured. Depending on the project, sensors, actuators, computers and communication are developed, specified or selected. Redundancy, diagnostic and fault concepts are taken into account.
- Develop hardware and embedded software: The electronic platform and software are developed in accordance with the defined architecture and the allocated requirements.
- Develop control functions: Algorithms are developed on the basis of the engine behaviour, the available sensor information, the actuator dynamics and the operating limits to be observed.
- Integrate the control unit and engine environment: Hardware, software, control functions, sensors and actuators are brought together step by step and connected to a real or simulated engine environment.
- Verify and qualify functions: Functions, interfaces and fault responses are tested against the defined requirements. Testing and validation, test systems and environmental testing support reproducible compliance demonstration.
Methods and standards for engine control
Technologies and methods
Depending on the project and development scope, physical modelling and simulation, model-based control development, safety assessments, diagnostic and redundancy concepts and end-to-end traceability are used. Assurance is provided through hardware-in-the-loop tests, test automation, environmental testing and qualification. On the HIL test bench, a real control unit can be operated in a simulated engine environment. This allows sensor values, actuator behaviour, operating states and defined faults to be examined reproducibly.
Relevant standards and guidelines
The applicable standards and evidence depend on the engine, platform, function, criticality, development scope and certification basis. Depending on the project, the following may be particularly relevant:
- SAE ARP4754B: Development of civil aircraft and systems
- SAE ARP4761A: Safety assessment process for civil aircraft and systems
- RTCA DO-178C: Software in airborne systems and equipment
- RTCA DO-254: Electronic hardware in airborne systems
- RTCA DO-160: Environmental conditions and test procedures for airborne equipment
- EASA CS-E or 14 CFR Part 33: Certification requirements for aircraft engines
- EN 9100: Quality management systems in aviation, space and defence
The applicable issues, compliance objectives and design assurance levels are defined for the specific project.
Applications of engine control
Typical fields of application include:
- FADEC systems and engine control units
- Engine monitoring
- Speed and power control, fuel control
- Sensor and actuator connection
- Protection, diagnostic and degradation functions
For electric and hybrid propulsion systems, Silver Atena offers services in electric and hybrid aircraft propulsion. Avionics and flight control functions outside engine control are covered under avionics and flight control.
Benefits for engine control projects
- Developing control unit and function together: Electronics, embedded software and control functions are developed and integrated on the basis of a common system architecture.
- Considering fault cases early on: Sensor, actuator, communication and computer faults are taken into account in the architecture and function development.
- Preparing integration systematically: Defined interfaces and test concepts support the step-by-step integration of control unit, sensors, actuators and engine environment.
- Building evidence consistently: Requirements, implementation and verification are linked and documented traceably.
Engine control across engineering disciplines
Engine control combines several development disciplines and is closely linked to system development, avionics and assurance.
- System and requirements: Requirements engineering describes requirements and interfaces. System architecture and system integration translate them into a technical structure.
- Hardware, software and control engineering: Hardware development provides the electronic platform. The embedded software implements hardware-related, communication and functional tasks. Control development designs the engine control, limiting and monitoring functions.
- Safety, testing and qualification: Safety engineering derives requirements for fault behaviour and architecture. Testing, test bench development and environmental testing support functional and environmental compliance demonstration.
Why Silver Atena for engine control?
- Cross-disciplinary development
System architecture, hardware, embedded software, control engineering, safety and verification are aligned through common requirements and interfaces. - Development through to integration and compliance demonstration
Depending on the project, our scope of services ranges from the concept through the control unit and function integration to verification and qualification. - Test bench and testing expertise
Test systems, automated testing and environmental testing can support functional and environmental assurance. The specific scope of services is defined for each project.
Engine control for your project
Are you looking to develop or further develop engine control units, FADEC functions or other engine control functions? Discuss your requirements and the development scope you need with our team.